Four locations were selected to represent the range of conditions found in the cotton growing area of southeastern Missouri. All locations were planted on 38" row spacing. Johnny Hux's farm near Sikeston (Bosket fine sandy loam soil), Charles Provance's farm near Clarkton (Bosket fine sandy loam soil), Charles Parker's farm near Senath (Dubbs silt loam soil). The trials at the Portageville location were planted at the UMC Delta Center's Lee Farm. Portageville irrigated trials were planted on Tiptonville sandy loam soil, while the Portageville clay trial was planted on Portageville Clay.

Field Plot Design: The trials were arranged in a randomized complete block design with four replications. The plots were four rows wide and 37 feet long, with the center two rows being used for yield and other data. Plots were end trimmed to 31 feet in length prior to harvest, to eliminate end plant effect.

Entries: All producers of cottonseed were eligible to enter varieties in the 2000 evaluation trials. Participation was voluntary and no control was exercised by the program over which or how many varieties were entered. However, to help finance the evaluation programs, a fee of $350 was charged for each variety entered by the seed producers. A total of 32 cotton varieties were compared in 2001, as outlined in the following table.

Table 1. Source of Cotton Entries Evaluation in 2001

Plot Management: The trials were planted with commercial equipment modified for small plot work. The fields were managed during the growing season by the producer/cooperator. Once-over harvest was completed using a Case 1822 picker. The seed cotton was ginned on a 20-saw Continental micro-gin equipped with an incline cleaner along with a single stage lint cleaner.

Data Recorded:Lint yields are reported in pounds of lint per acre. H.V.I. quality characteristics of the lint were analyzed at the International Textile Center in Lubbock, Texas and the results are presented with the yield and other agronomic data.

Fiber Quality: Fiber quality characteristics were determined for each variety utilizing lint samples from all replications at each test location. These characteristics and their importance are described below.

A: Micronaire (Mic): The micronaire test provides a combined measure of maturity and fineness of cotton fibers. Fiber maturity is a relative measure of cell-wall thickening. Immature fibers result in the production of yarns and fabrics with low quality. In the test, air is passed through a compressed sample of cotton fiber. The rate of flow through the sample follows a relationship between diameter or thickness of the textile fibers and the air resistance they provide. Finer fibers result in greater resistance and therefore, a lesser air flow. Micronaire values that are very low or very high are undesirable. A low micronaire implies the fiber is either fine or immature. A high micronaire is indicative of a very coarse fiber. Value recorded can be interpreted as follows: Below 3.6 = fine and often immature 3.7 - 4.9 = premium range Above 4.9 = coarse fibers

B: Uniformity: Fiber uniformity is a measure of the degree of uniformity of fiber length in a sample. Uniformity is calculated as a ratio of the average length of all fibers to the average length of the longest half of the fibers in the sample. The ratio is then multiplied by 100. High uniformity values are desirable and indicate uniform fiber lengths.

Below 77.0 = Very Low
77.1 - 79.0 = Low
79.1 - 82.0 = Average
82.1 - 85.0 = High
Above 85.1 = Very High

C: Strength: Fiber strength is reported in grams per tex. A tex unit is equal to the weight in grams of 1000 m of fiber. The strength values are reported in grams of force required to break one tex unit if fibers with the holding jaws separated 1/8 in. The 1/8 in. jaw spread breaks the fibers at the weak point. High fiber strength enables the yarn to be spun at a faster rate and produces a stronger yarn. The following chart categorizes strength readings and aids in the interpretation of strength values for an 1/8 in. gauge.

Below 23.9 = Very Low 24.0 - 26.9 = Low 27.9 - 29.9 = Average Above 30.0 = High

D: Length: Fiber length is reported in hundredths of an inch as measured by a fiber-graph instrument and is the average of the longest half of the fibers in the sample, upper half mean (UHM). Long fibers are desirable because they produce greater yarn strength and aid in spinning finer yarns.

Below 0.97 = Short
0.97 - 1.10 = Medium
1.11 - 1.28 = Long
Above 1.28 = Extra Long

E: Elongation: Elongation is the percent of fiber length that a fiber will stretch or elongate before it breaks. A high elongation is desirable and indicated that a fiber is not brittle.

F: Leaf: Leaf is the percent of the sample surface area that is covered by trash particles such as leaf fragments, bark and grass. High leaf content indicates that the sample will have a high waste content when spun.

G: Rd: Rd is the amount of light reflected by a sample. A high reflectance, which is desirable, indicates a bright sample of lint that is unweathered and undamaged as far as color is concerned.

H: +b: The amount of yellowness in a sample is measured as +b. Weathering and damaged lint such as caused by insect damaged locks will cause a high yellowness reading, which is undesirable. Lint that has a high level of yellowness will require more bleaching than lint that has a low level. Spots in samples will increase the +b reading

Site maintained by people at AgEBB
agebb@missouri.edu